Samson Media 7 Mounting And Operating Instructions Download Page 47

Page: 47 / 96

EB 9510 EN

Optional additional function

6.2.2 Installing the GSM

module

The GSM module unit consists of the module
(including SIM card) and the right-angle an-
tenna with cable and SMA bushing.

Incorrect installation and removal of GSM
module will damage the differential pressure
meter.

Before inserting or removing the GSM

module, disconnect the power supply.

Electrostatic discharge will damage the GSM
module and SIM card.

−

Observe the ESD requirements according

to IEC 61340-5-1.

−

Store the GSM module and SIM card in

their packaging.

Incorrect installation and removal of SIM
card will damage it.

Before inserting or removing the SIM card,

disconnect the power supply.

Housing

Right-angle antenna

3 Nut

4 Toothed lock washer

5 O-ring

6 SMA bushing

7 Male connector

8 Female connector

9 Fastening screw

Use a TORX

T10

screwdriver.

Fig. 13:

Installing the GSM module

NOTICE

Summary of Contents for Media 7

































































































Search results

Summary of Contents for Media 7

Reviews:

Brands by name

Popular brands

Samson Media 7, Mounting And Operating Instructions

Search results

Summary of Contents for Media 7

Reviews:

Brands by name

Popular brands