10-030
TROUBLESHOOTING
2-4. Vibration
Check following items before troubleshooting.
No blown fuses and power is applied up to fuses.
Throttle lever must be “FULL”.
Check any ground circuit which belongs to components to be checked.
2-4-1. No vibration occurs 1/2
F-R lever must be “F” or “R”.
Vibration mode select switch must be “AUTO” (automatic mode).
Reference Fig.: 2-4-1
Check point
Check/Cause
Action
1. Vibrator Solenoid
Disconnect harness and measure resistance of coil.
Standard resistance
SW/TW354
: 8.6 to 8.8 Ω
TW504
: 5.42 Ω
If measured resistance is abnormal, vibrator solenoid is
faulty.
•
•
Replace vibrator
solenoid.
2. Vibration Mode Select
Switch
(1) When starter switch is ON, measure voltage between
vibration mode select switch terminal 4 inlet wire RL
and chassis ground.
Standard voltage : 12 V or more
(2) When starter switch is ON, measure voltage between
vibration mode select switch terminal 5 outlet wire BrY
and chassis ground.
Standard voltage : 12 V or more
If above item (1) is OK and item (2) is NG, vibration mode
select switch is faulty.
•
Replace vibration mode
select switch.
3. Vibratory Drum Select
Switch
(SW354 ROPS)
(1) When starter switch is ON, measure voltage between
vibratory drum select switch terminal 1 inlet wire RL,
terminal 4 inlet wire RL and chassis ground.
Standard voltage : 12 V or more
(2) When starter switch is ON and vibratory drum select
switch is in “
”, measure voltage between vibratory
drum select switch terminal 6 outlet wire LgR and
chassis ground.
Standard voltage : 12 V or more
(3) When starter switch is ON and vibratory drum select
switch is in “
”, measure voltage between vibratory
drum select switch terminal 6 outlet wire LgR, terminal
3 outlet wire LgB and chassis ground.
There is no electricity in normal condition.
(4) When starter switch is ON and vibratory drum select
switch is in “
”, measure voltage between vibratory
drum select switch terminal 3 outlet wire LgB and
chassis ground.
Standard voltage : 12 V or more
If above item (1) is OK and item (2), (3) or (4) is NG,
vibratory drum select switch is faulty.
•
Replace vibratory drum
select switch.
•
•
•
•
•
Summary of Contents for SW354
