Sakai SW354 Shop Manual Download Page 283 | Manualshive

Page: 283 / 480

background image

6-033

VIBRATORY DRUM • REAR WHEEL

(NOTICE)

Push in the inner race while rotating the bearing.
Otherwise, even strongly trying to push the inner
race, the bearing rollers will not be pushed up and
therefore bearing will not be seated.

③

Remove bolts (23).

Remove cover (24).

Remove shim.

(NOTICE)

Do not turn the disc subassembly after the cover is
removed.

④

Without inserting shim, install cover (24) to boss

subassembly with four bolts (23) and washers.

•

•
•

•

SW800-06080

End of rollers in close

contact with inner race shoulder

Ga

p

Ga

p

(1) Bearing not

seated

(2) Bearing correctly

seated

SW354-06070

23

24

Shim

SW354-06036

23

24

Boss

subassembly

«
...
281
282
283
284
285
...
»

Summary of Contents for SW354

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SW354

Brand: B&K Pages: 8

Brand: Parker Pages: 54

Brand: NEC Pages: 29

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Peripheral Vascular Pages: 44

Brand: EAW Pages: 2

Brand: abc Pages: 28

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Sagola Pages: 62

Tacx Boost Bundle

Brand: Garmin Pages: 12

Brand: B&G Pages: 16

Brand: LABORIE Pages: 116

Brand: Teac Pages: 1

Brand: Garelick Pages: 2

Brand: American DJ Pages: 12

Brand: aion Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands