Sakai SW354 Shop Manual Download Page 329 | Manualshive

Page: 329 / 480

background image

9-017

INSPECTION AND ADJUSTMENT

12. ADJUSTMENT OF THROTTLE LEVER

12-1. Adjustment of Linkage

In cases such as maximum no-load rotational speed or
minimum no-load rotational speed deviating from standard
value, control cable is replaced, or throttle lever does not
move smoothly, make an adjustment in accordance with
procedure described below.
Make the adjustment after amply warming up engine.
Oil temperature during measurement : 50

± 5

°C (122

± 9

°F)

①

Set throttle lever (1) to “IDLE”.

②

Attach control cable (4) to throttle lever (1).

③

Attach control cable (4) to fuel injection pump’s control
lever.

④

Start the engine.

⑤

Loosen lock nut (3).

⑥

Using stopper bolt (2), adjust so that standard minimum
no-load rotational speed is achieved.

Standard minimum no-load rotational speed

: 1,050

± 50

rpm

⑦

Using lock nut (3), firmly secure stopper bolt (2).

⑧

Set throttle lever (1) to “FULL”.

⑨

Loosen lock nut (6).

⑩

Using stopper bolt (5), adjust so that standard maximum
no-load rotational speed is achieved.

Standard maximum no-load rotational speed

: 2,200

± 50

rpm

⑪

Using lock nut (6), firmly secure stopper bolt (5).

•

•
•

★

★

SW354-09016

1

IDLE

2
3

4

SW354-09030

1

FULL

5

6

«
...
327
328
329
330
331
...
»

Summary of Contents for SW354

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SW354

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Parker Pages: 39

Brand: Vaisala Pages: 2

Brand: GE Pages: 37

Brand: DeLaval Pages: 26

E-Boxx EV Simulator

Brand: Walther Pages: 12

GE cirrent Tetra Rigid Light Bar

Brand: Daintree Pages: 9

GYRONETICS E-Series

Brand: gorilla sports Pages: 22

Z100-M618.03 S5V

Brand: Jäger Pages: 40

Brand: Pari Pages: 318

Brand: Panblast Pages: 5

Brand: Magnum Industrial Pages: 10

Digital Delay DD-6

Brand: Boss Pages: 28

Brand: BIOTRONIK Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands