Sakai SW354 Shop Manual Download Page 277

Page: 277 / 480

6-027

VIBRATORY DRUM • REAR WHEEL

20) Secure three dampers (36) to disc subassembly with six /

twelve bolts (35) and washers.

N•m

(35) Bolts

SW/TW354 (six bolts) : M16×40 : 265 N·m (195 lbf·ft)

TW504 (twelve bolts) : M12×30 : 108 N·m ( 80 lbf·ft)

WARNING

Be careful because reversing the vibratory drum

involves risk. Confirm that the surrounding area is safe,

and work in a natural, unstrained posture.

21) Reverse drum subassembly.

Drum subassembly

SW/TW354 : 500 kg (1,102 lbs.)

TW504

: 790 kg (1,742 lbs.)

22) Reassembly of boss subassembly

22-1) Apply a coat of gear oil to boss (8) at where bearing

will be press-fitted.

Drive in vibrator bearing (7).

•

SW354-06019

SW300-1-06054

Drum

subassembly

SW300-1-06057

Wooden block

Summary of Contents for SW354

































































































































































































































































































































































































































































































Search results

Summary of Contents for SW354

Reviews:

Related manuals for SW354

Brands by name

Popular brands

Sakai SW354, Shop Manual

Search results

Summary of Contents for SW354

Reviews:

Related manuals for SW354

Brands by name

Popular brands