Sakai SW352 Service Manual Download Page 160

Page: 160 / 176

5-128

Disassembly and Assembly of Propulsion Motor Negative Brake

13. Disassembly and Assembly of Propulsion Motor

Negative Brake

13-1. Disassembly of propulsion motor negative brake

1. Brake cover

Slacken eight socket head cap screws (2)
fastening brake cover (1).

Loosen the screws evenly, since brake
spring (3) attempts to lift brake cover (1).

If the screws are not slackend evenly, the

last screw is likely to break.

Screw size

DCM0280

M6X20L

5 mm

DCM0560

M8X25L

6 mm

Width across flats

2. Brake spring

When brake cover (1) is removed, brake
spring (3) will appear. Remove the spring.

3. Preparation for brake piston removal

After removing O-ring and socket head plugs
with O-ring fitted from the forced brake
release port, position brake cover (1) on the
brake housing. Keep the brake release pilot
port (4) open to vent residual pressure.

TW5025059

TW5025060

TW5025061

Summary of Contents for SW352

















































































































































































Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands

Sakai SW352, Service Manual

Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands