Sakai SW352 Service Manual Download Page 151

Page: 151 / 176

5-119

1. Hydraulic hose

1) Remove the floor board by the operator’s

seat.

2) Remove seven hoses (1)–(3).

★

Blank the open ends of hoses and
adapters.

Removal and Installation of Center Pin Assembly

4. Throttle cable & F-R cable

1) Take off Orbitrol cover.

2) Remove throttle cable (6) and position it

close to the front frame.

3) Remove F-R cable (7) and position it close

to the front frame.

2. Electric wiring

Detach connectors (4) and place the hoses
close to the front frame so that they may not
interfere with the work.

3. Sprinkler

Disconnect hoses (5) and put them close to
the front frame.

8. Removal and Installation of Center Pin Assembly

8-1. Removal of center pin assembly

Disconnect battery negative (–) cable.

TW5025043

TW5025044

TW5025045

Summary of Contents for SW352

















































































































































































Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands

Sakai SW352, Service Manual

Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands