Sakai SW352 Service Manual Download Page 148

Page: 148 / 176

5-116

Disassembly and Assembly of Front Drum Assembly

3. Disc

1) Using lifting bolts, install disc (16) to

propulsion motor assembly. Tighten six
securing bolts (15).

・

Tightening torque: 343 N·m (35 kgf·m)

2) Install elbos (10)–(14).

5. Axle shaft

1) Using lifting bolts, assemble axle shaft (9)

onto the vibrator shaft. Tighten the eight
fixing bolts.

・

Tightening torque: 265 N·m (27 kgf·m)

4. Vibrator shaft end float

★

Make sure that the vibrator shaft has an
end float of about 2.5 mm (0.1 in)

2) Assemble bearing (12) onto axle shaft

(9).

★

Apply lithium grease to the
bearing.

TW5025031

About 2.5mm (0.1 in)

TW5025038

TW5025039

Lifting bolt

TW5025040

Apply grease.

Summary of Contents for SW352

















































































































































































Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands

Sakai SW352, Service Manual

Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands