Sakai SW352 Service Manual Download Page 175

Page: 175 / 176

Removal and installation of Orbitrol

5-143

17. Removal and installation of Orbitrol

17-1. Removal of Orbitrol

1. Cover

Remove the cover under the instrument
panel.

2. Orbitrol

1) Disconnect four hoses (2).

★

Before disconnection, label the hoses
for correct reconnection.

★

Plug the open ends of the hoses and
openings of Orbitrol.

2) Remove four bolts (3) and remove steering

wheel assembly (4) together with Orbitrol
(5).

Hold Orbitro by hand, as it can fall free
when the steering wheel is detached.

SW5005085

17-2. Installation of Orbitrol

★

Reverse the removal instructions.

★

Add oil to the tank to make up for a leak.

★

Start the engine and let oil circulate through
the piping. Then recheck the oil level.

Summary of Contents for SW352

















































































































































































Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands

Sakai SW352, Service Manual

Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands