Sakai SW352 Service Manual Download Page 157

Page: 157 / 176

5-125

Removal and Installation of Propulsion/Vibration/Steering/Charge Pump Assembly (SW352, SW502)

★

Install by reversing the removal procedure.

[

Tightening torque setting of propulsion pump
securing bolts: 108 N·m (11.0 kgf·m)

[

Tightening torque setting of vibrator/steering/
charge pump securing bolts: 49 N·m (5.0 kgf·m)

Adjust linkage referring to “Adjustment of F-R
lever linkage stroke”, page 3-109.

★

Apply lithium grease to the splined portion
of the pump.

★

Add oil to the tank to the spceified level for
compensation of a leak.

★

Start and run the engine to allow oil to circu-
late through the piping. Recheck the oil level.

★

Remove the assembly referring to steps 7
to 9 in “Removal of engine and propulsion/
vibration/steering/charge pump assembly”,
page 5-104.

1) Temporarily lift and hold the propulsion/

vibration/steering/charge pump assembly
and remove two bolts (2) that fasten the
clutch housing to propulsion pump (1). [

2) Lift off the propulsion/vibration/steerig/

charge pump assembly.

3) Remove two bolts (4) that fix vibration/

steering pump assembly (3) to propulsion
pump (1) and remove the assembly.

[

10. Removal and Installation of Propulsion/Vibration/

Steering/Charge Pump Assembly (SW352, SW502)

10-1. Removal of propulsion/vibration/steering/charge pump assembly

10-2. Installation of propulsion/vibration/steering/charge pump assembly

TW5025056

Summary of Contents for SW352

















































































































































































Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands

Sakai SW352, Service Manual

Search results

Summary of Contents for SW352

Reviews:

Related manuals for SW352

Brands by name

Popular brands