Sakai SV410-2 Shop Manual Download Page 245

Page: 245 / 270

9-040

TROUBLESHOOTING

2-5-2. Combination meter warning lamp or indicator lamp is abnormal

Reference Fig. : 2-5-1

Check point

Check/Cause

Action

1. Each Bulb

Check that none of lamp bulbs is burned out or has a

contact failure (charge warning lamp, engine oil pressure

warning lamp, hydraulic oil filter warning lamp and parking

brake indicator lamp).

Bulb is faulty or poorly connected.

•

Replace each bulb.

2. Lamp Check Relay

(R4)

(1) when starter switch is ON, measure voltage between

lamp check relay terminal 2 outlet wire LgB and chassis

ground.

Standard voltage : 12 V or more

(2) when starter switch is ON, measure voltage between

lamp check relay terminal 5 outlet wire B and chassis

ground.

Standard voltage : 12 V or more

(3) After starting engine, measure voltage between lamp

check relay terminal wires and chassis ground.

Lamp check relay terminal 2 inlet wire LgB and

chassis ground

Lamp check relay terminal 5 outlet wire B and chassis

ground

There is no electricity in normal condition.

If above item (1) is OK and item (2) is NG, lamp check

relay is faulty.

If above items (1) and (2) are OK and item (3) is NG,

alternator is faulty.

•

Repair or replace lamp

check relay (R4) or

alternator.

3. Combination Meter

(Lamp check)

(1) when starter switch is ON, measure voltage between

combination meter battery terminal wire No. 35 inlet

wire YW and ground terminal wire B.

Standard voltage : 12 V or more

(2) when starter switch is ON, check that parking brake

indicator lamp, hydraulic oil filter warning lamp, engine

oil pressure warning lamp and electrical charge warning

lamp illuminate and then go out after starting engine.

If above item (1) is OK and the item (2) is NG,

combination meter is faulty.

(NOTICE)

Since engine cannot start unless parking brake

switch is applied and F-R lever is “N”, parking brake

indicator lamp does not go out even after starting

engine.

•

Replace combination

meter.

4. Harness Connecting

Between Terminals

Measure resistance of harness connecting between

terminals.

Standard resistance : 10 Ω or less

If resistance is abnormal, harness is faulty.

•

Repair or replace

harness.

Summary of Contents for SV410-2















































































































































































































































































Search results

Summary of Contents for SV410-2

Reviews:

Related manuals for SV410-2

Brands by name

Popular brands

Sakai SV410-2, Shop Manual

Search results

Summary of Contents for SV410-2

Reviews:

Related manuals for SV410-2

Brands by name

Popular brands