Sakai SV400D-2 Shop Manual Download Page 162

Page: 162 / 218

8-014

MEASUREMENT AND INSPECTION OF STEERING CIRCUIT PRESSURE

8. MEASUREMENT AND INSPECTION OF STEERING CIRCUIT

PRESSURE

8-1. Measurement

Before turning the steering wheel, confirm that

no one is near the vehicle’s bends spots.

Oil temperature during measurement: 50 ± 5°C
(122 ± 41°F)

①

Remove the hose (1) from the steering pump’s

discharge side (1 1/16 – 12UN). Attach the
pressure gauge through the adapter

Adapter size: G3/4
Pressure gauge: 0 – 24.5 MPa (0 – 3553 psi)

②

Confirm that the forward-reverse lever is

properly in the neutral position.

③

Start the engine. Then move the throttle lever to

the high idling position.

④

Turn the steering wheel and measure the

steering hydraulic circuit maximum pressure.

Maximum standard circuit pressure

: 17.5 ± 1.0 MPa (2538 ± 145 psi)

•

SV400-2-08010

Steering pump

SV400-2-08010

Steering pump

SV400-2-08020

Summary of Contents for SV400D-2



























































































































































































































Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands

Sakai SV400D-2, Shop Manual

Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands