Sakai SV400D-2 Shop Manual Download Page 156

Page: 156 / 218

8-008

MEASUREMENT OF PARKING BRAKE RELEASE PRESSURE

5. MEASUREMENT OF PARKING BRAKE RELEASE PRESSURE

5-1. Measurement

Oil temperature during measurement

: 50 ± 5°C (122 ± 41°F)

①

Disconnect the hose (2) that is connected to the

brake solenoid valve (1). Attach the pressure
gauge through the adapter

Gauge port: G1/4
Pressure gauge: 0 – 4.9 MPa (0 – 711 psi)

②

Confirm that the forward-reverse lever is in the

“neutral position”.

③

Press the parking brake switch and turn the

parking brake “ON”.

④

Start the engine. Then move the throttle lever to

the high idling position.

⑤

Turn the parking brake switch “OFF”, and

measure the brake release pressure.

Standard charge relief pressure setting

: 2.5 ± 0.2 MPa (363 ± 29 psi)

•

•
•

SV400-2-08006

Summary of Contents for SV400D-2



























































































































































































































Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands

Sakai SV400D-2, Shop Manual

Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands