Sakai SV400D-2 Shop Manual Download Page 155

Page: 155 / 218

8-007

MEASUREMENT OF VEHICLE HIGH/LOW-SPEED CHANGE CIRCUIT PRESSURE

4. MEASUREMENT OF VEHICLE HIGH/LOW-SPEED CHANGE

CIRCUIT PRESSURE

4-1. Measurement

Oil temperature during measurement

: 50 ± 5°C (122 ± 41°F)

①

Remove the plugs from the rear propulsion

motor’s gauge ports (4) and (5). Attach the
pressure gauge through the adapter

Gauge port: 9/16-18UNF
Low-speed-side gauge port: (5)
High-speed-side gauge port: (4)
Pressure gauge: 0 – 4.9 MPa (0 – 711 psi)

②

Press the parking brake switch, turn the parking

brake “ON” and move the speed change switch
to the “Low” or “High” position.

③

Start the engine, move the throttle lever to the

high idling position, and measure the pressure.

Standard charge relief pressure setting

: 2.5 ± 0.2 MPa (363 ± 29 psi)

•

•
•
•
•

SV400-2-08005

Summary of Contents for SV400D-2



























































































































































































































Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands

Sakai SV400D-2, Shop Manual

Search results

Summary of Contents for SV400D-2

Reviews:

Related manuals for SV400D-2

Brands by name

Popular brands