background image

 
 

 

Safretti Mistero 500, Mistero 1000  

 

Introduction 

Please read this information guide carefully to be able to safely install, use and maintain your product.  

Important Safety Advice 

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, 
electrical shock and injury to persons, including the following: 

If the appliance is damaged, check with the supplier before installation and operation. 

Do not use outdoors. 
Do not use in the immediate surroundings of a bath, shower or swimming pool. 
Do not locate the appliance immediately below a fixed socket outlet or connection box. 

This appliance can be used by children aged from 8 years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not 
play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. 

Children of less than 3 years should be kept away unless continuously supervised. 
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been 
placed or installed in its intended normal opening position and they have been given supervision or instruction 
concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years 
and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. 
 

CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be 
given where children and vulnerable people are present. 
 
Do not use this appliance in series with a thermal control, a program controller, a timer or any other device that 
switches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced. 
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 meter from the 
appliance. 
In the event of a fault unplug the appliance. 
Unplug the appliance when not required for long periods. 
Although this appliance complies with safety standards, we do not recommend its use on deep pile carpets or 
on long hair type of rugs. 
The appliance must be positioned so that the plug is accessible. 
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified 
person in order to avoid a hazard. 
Keep the supply cord away from the front of the appliance. 
  
WARNING: In order to avoid overheating, do not cover the appliance. Do not place material or garments on 
the appliance, or obstruct the air circulation around the appliance. 
  
 

 

 

Summary of Contents for Magic-Fire MISTERO 500






















Reviews: