Saab 2004 9-5 Owner'S Manual Download Page 278 | Manualshive

Page: 278 / 288

background image

278

Specifications

Wheels and tires
(recommended dimensions)

2.3t

2.3 Turbo

2.3T

Summer tires

205/65 R15 94 V

X

–

–

215/55 R16 93 V

X

X

X

225/45 R17 94 W XL/RF

X

X

X

Winter tires

205/65 R15 94 Q

X

–

–

205/55 R16 91 Q

X

X

X

215/55 R16 93 Q

X

X

X

225/45 R17 94 Q XL/RF

X

X

X

Wheel sizes

6 x 15”

X

–

–

6,5 x 16”

X

X

X

7 x 17”

X

X

X

15" wheels must not be fitted to the 2.3 Turbo and 2.3T since the size of
the brake discs prohibits this.

Speed ratings and load indices, see page 241.
Always contact an authorized Saab dealer if you wish to fit other wheels
or tires than those fitted as standard.

Compact spare:

Wheel ___________________________ 4 x 16

Tire _____________________________ T115/70 R16

Pressure_________________________ 60 psi (420 kPa)

Maximum life _____________________ 2,200 miles

(3500 km)

Maximum speed __________________ 50 mph (80 km/h)

NOTICE

Snow chains:

Snow chains must not be fitted to the rear wheels, and may only
be used with the following wheel-tire combinations:

Wheels

Tires

6 x 15*)_____ 205/65 R15

6.5 x 16_____205/55 R16 M+S or

215/55 R16

Snow chains must not be fitted to 17" wheels.

Max. permissible speed with snow chains fitted is 30 mph
(50 km/h).

Contact an authorized Saab dealer for advice on snow chains.

NOTICE

Wheels larger than 17” must not be fitted.

Wheel offset must be 49 mm.

Vehicles with 12.05 in (306 mm) front brake discs must not use
15” rims.

«
...
276
277
278
279
280
...
»

Summary of Contents for 2004 9-5

































































































































































































































































































Reviews:

No comments

Related manuals for 2004 9-5

Brand: Jeep Pages: 25

Brand: kaarta Pages: 29

Brand: Pacbrake Pages: 14

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: PullRite Pages: 10

Brand: Tessera4x4 Pages: 20

Brand: Thule Pages: 8

Quattroporte Automatic

Brand: Maserati Pages: 272

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Jeep Pages: 1528

Brand: Ranger design Pages: 22

Quantum hardcoated N30216

Brand: National Cycle Pages: 3

Brand: mtf TRANSPORT SYSTEM Pages: 9

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Mitsubishi Pages: 362

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands