Saab 2004 9-5 Owner'S Manual Download Page 129 | Manualshive

Page: 129 / 288

background image

129

Interior equipment and trunk

To open:

• Slide the control towards the rear to open

the sunroof to the comfort position.
To open it fully, slide the control back a
second time. Press the control to stop it
earlier.

To close:

• Slide the control forwards until the sunroof

is closed.

Ventilation position

• Press the middle of the control (when sun-

roof closed).

• To close: slide the control forwards.
To fully open the sunroof from the ventila-
tion position, slide the control back.

The sunroof incorporates an interior, man-
ual, sliding sun blind.
After the car has been waxed, the sunroof
may squeak or squeal on opening to the
ventilation position. If this should occur, fully
open the sunroof and, using washer fluid,
wash the seal along the front edge, together
with the paintwork that is in contact with the
seal when the roof is closed.

Emergency operation of sunroof

In an emergency (e.g. if there is an electrical
failure) the sunroof can be operated by a
screwdriver. Remove the cover at the front
of the sunroof opening, insert a screwdriver
in the groove, and rotate.
Rotate counterclockwise to close sunroof.

IB430

1

3

2

Sunroof control

1 To open
2 To close
3 Ventilation position

IB431

Manual operation of sunroof

«
...
127
128
129
130
131
...
»

Summary of Contents for 2004 9-5

































































































































































































































































































Reviews:

No comments

Related manuals for 2004 9-5

Brand: Hama Pages: 6

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 209

Brand: VBC Racing Pages: 34

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 236

Brand: Porsche Pages: 144

Brand: Ford Pages: 12

Brand: Trailboss Pages: 5

Brand: TATA Motors Pages: 159

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Thule Pages: 8

Brand: GMC Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands