Saab 2004 9-5 Owner'S Manual Download Page 134 | Manualshive

Page: 134 / 288

background image

134

Interior equipment and trunk

Cup holders

Cup holders are provided in the instrument
panel fascia, in the center console compart-
ment between the front seats, and in the
rear-seat armrest (certain variants only).
To access the cup holder in the instrument
panel, press the symbol and release.
To access the cup holder in the rear seat
armrest, lower the armrest and press the
front edge of the holder. Close in the same
way.
The number of cup holders provided may
vary between models.

WARNING

• The cup holder should not be used to

hold cups made of china, glass or hard
plastic as these can cause injury in the
event of a crash.

• Use only for paper cups or aluminium

cans.

• Avoid spillage, particularly of hot

drinks.

• Avoid putting oversized cups in the

cup holder.

NOTICE

Take care not to spill any liquid on the
audio system when using the cup
holders. Soft drinks in particular can
cause malfunction.

IB1

153

1

2

Cup holder in center console

IB443

Cup holder in rear armrest (certain vari-
ants only)(
Press the edge to open/close.

IB444

Cup holder in fascia

1 Press symbol to open
2 Lift bottom to close

«
...
132
133
134
135
136
...
»

Summary of Contents for 2004 9-5

































































































































































































































































































Reviews:

No comments

Related manuals for 2004 9-5

Brand: Westin Pages: 3

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: Renault Pages: 238

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Honda Pages: 85

Brand: Yakima Pages: 13

SANICON TURBO 300

Brand: Thetford Pages: 25

Brand: EUFAB Pages: 4

Brand: Subaru Pages: 16

Brand: Mercedes-Benz Pages: 493

Brand: Easee Pages: 21

Brand: Mazda Pages: 604

Brand: Saab Pages: 498

Brand: Kargo Master Pages: 8

Brand: Chevrolet Pages: 324

Brand: Saab Pages: 9

Brand: Falcon Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands