manualshive.com logo in svg

Saab 2004 9-5, Owner'S Manual

The Saab 2004 9-5 Owner's Manual is a comprehensive guide to help you navigate every aspect of your vehicle. Packed with essential information, this manual allows you to download and access it for free from manualshive.com, ensuring you have the necessary tools to enjoy your Saab to the fullest.

Share
Download
background image

190

Starting and driving

Towing the car 

Gear lever in neutral (in cars with automatic 
transmission: selector lever at N (neutral)) 
Turn on the parking lights.
Drive carefully and do not exceed the 
speed limit for vehicles being towed. 
Always try to keep the towrope taut by 
gently applying the brake, as necessary. 
This will avoid the towrope being jerked 
violently.

The local regulations on towing speeds 
must be followed.
The highest permissible towing speed is 
30 mph (50 km/h), unless the legal limit is 
lower. The longest permissible towing dis-
tance is 30 miles (50 km). If the car has to 
be transported farther than that, summon a 
tow truck. A flat bed tow truck is the pre-
ferred method to tow.
Failure to follow these guidelines can result 
in damage.

Cars with automatic transmission

The car cannot be bump started. In an 
emergency, it is possible to start the engine 
using jump leads (see the section, ”Jump 
starting” on page  191).

Transporting the car 

NOTICE

• Never use the towing eyes to pull the 

car unstuck.

NOTICE

• The car must be towed front first.

• If the car is to be towed with the front 

wheels off the ground, make sure the 
parking brake is off, as this acts on the 
rear wheels. 

NOTICE

If a car with a sport (lowered) chassis is 
transported, for example on a flat bed 
truck, take extra care not to damage the 
spoiler and/or underbody.

Never use the towing eyes to pull the car 
unstuck

Summary of Contents for 2004 9-5

































































































































































































































































































Reviews:

No comments

Related manuals for 2004 9-5

iDataLink Maestro Installation Manual preview
Maestro
Brand: iDataLink Pages: 9
Harken Hoister SUP Manual preview
SUP
Brand: Harken Hoister Pages: 12
Yamaha Raptor Instruction Supplement preview
Raptor
Brand: Yamaha Pages: 2
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Xblitz G250 User Manual preview
G250
Brand: Xblitz Pages: 16
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
Saab 32 025 888 Installation Instructions preview
32 025 888
Brand: Saab Pages: 3
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
Camoplast T4S Installation Manuallines preview
T4S
Brand: Camoplast Pages: 19
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Brand: Tesla Pages: 274
Mazda 2006 MPV Quick Tips preview
2006 MPV
Brand: Mazda Pages: 14
Yakima K1095 Instructions Manual preview
K1095
Brand: Yakima Pages: 12
Opel MERIVA 2014 Brochure & Specs preview
MERIVA 2014
Brand: Opel Pages: 44
Setma E12AU02002 Instruction Manual preview
E12AU02002
Brand: Setma Pages: 16
Chevrolet Chevelle 1965 Owner'S Manual preview
Chevelle 1965
Brand: Chevrolet Pages: 55
Blue Bird TC/2000 Owner'S Manual preview
TC/2000
Brand: Blue Bird Pages: 111

Brands by name

Popular brands

Load more brands