background image

8 — English

OPERATION

WARNING: 

Do not allow familiarity with this product to make you 
careless. Remember that a careless fraction of a second is 
sufficient to inflict serious injury.

WARNING: 

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1. Failure to do so could result 
in fluids entering your eyes resulting in possible serious 
injury.

WARNING:

Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of 
attachments or accessories not recommended can result 
in serious personal injury.

APPLICATIONS

You may use this product for the purpose listed below:

 

Interior and exterior painting and staining of decks, 
outdoor furniture, fences, and walls

WARNING:

Risk of fire or explosion. Spray area must be well-venti-
lated and away from sparks or flames.

FILLING SPRAYER WITH PAINT/STAIN

See Figures 3 - 4, page 12.

Remove and discard any skin that has formed on top of the 
paint or stain, then thoroughly mix the material in its original 
container before beginning. 

NOTE: 

Older containers of stain and paint may need to be 

strained before use.

 

Unplug the sprayer.

 

Remove the quick-lock container by twisting 
counterclockwise so that the arrow on the container 
lines up with the “unlock” symbol on the lid.

 

Fill the container with paint or stain as desired. Do not fill 
above the max fill (1.5 qt.) mark on the container.

 

Reinstall the container on the sprayer and twist clockwise 
so that the arrow on the container lines up with the “lock” 
symbol on the lid.

WARNING:

To reduce the risk of injection, do not point sprayer at 
any part of the body or person. In case of skin injection, 
seek medical attention immediately. Do not use without 
spray tip in place.

OPERATING THE SPRAYER

See Figures 5 - 7, pages 12 - 13.

  Ensure the surface to be painted is free of dust, dirt, and 

grease.

  Mask or cover any areas not intended to be painted or 

stained. Be aware of wind that may cause your paint or 
stain to spray into areas not desired. Always use drop 
cloths or other cover to protect areas that are not intended 
to be painted or stained.

  Place a line of lubricant on the piston. To gain access to 

the piston, follow the instructions in 

Cleaning the Sprayer 

for Storage 

in the 

Maintenance 

section of this manual.

  Re-assemble the spray tip assembly.

  The tip guard may be set to spray paint in either a 

horizontal or vertical pattern.  To change the direction 
of the spray, loosen the metal collar of the spray tip 
assembly by turning it clockwise. Adjust the spray tip 
and tip guard as shown, and tighten the metal collar to 
secure the spray tip assembly.

  Fill the quick-lock paint container with no more than  

1.5 quarts of desired paint or stain.

  Plug in the sprayer.

  Pull the switch trigger to spray paint. Release the switch 

trigger to stop paint spray.

  Practice spraying on a piece of scrap material to test your 

spray pattern and to prime the pump before beginning. If 
you cannot get a good spray pattern with an even amount 
of paint or stain throughout, refer to the 

Troubleshooting

 

section later in this manual.

 

NOTE: 

The pump must be primed after every paint 

change and at first use after storing. Spray paint at a 
scrap surface for at least 20 seconds to prime.

 

To create an even coating over the entire surface:

 

  Move your arm at a steady rate of speed and make 

sure to move your entire arm, not just your wrist.

 

  Keep the sprayer an even distance from the area 

being sprayed, which should be between 8 to 10 
inches from the tip of the sprayer to the surface 
being sprayed.

Summary of Contents for SSP300





































Reviews: