8 — English
MAINTENANCE
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine or motor, wait for all moving parts to stop,
and disconnect spark plug wire and move it away from
spark plug or disconnect from power supply. Failure to
follow these instructions can result in serious personal
injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
When servicing, use only recommended or equivalent
replacement parts. Use of any other parts could create
a hazard or cause product damage.
NOTICE
:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced. Please contact customer service or a qualified
service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or de-
stroy plastic which could result in serious personal injury.
LINE REPLACEMENT
See Figures 7 - 8.
For gas and electric power heads, use 0.080 in. or 0.095 in.
trimmer line. For cordless power heads, use 0.080 in. trim-
mer line only.
Stop the unit and disconnect the spark plug wire for gas
power heads, remove the battery pack for cordless power
heads, or disconnect from power supply for electric power
heads.
Rotate the bump knob clockwise as necessary to align the
arrows on the bump knob with the arrows on the string
head housing.
Cut one piece of trimmer line 16 ft. long. Insert the line
into the eyelet on the string head housing. Push until the
end of the line comes out the other side of the housing.
Pull the line until equal amounts of line appear on both
sides of the housing.
NOTE:
Line may jam if more than 16 ft. is loaded.
Either by hand or using the SPEED WINDER
™
, rotate the
bump knob clockwise to wind the line on the spool until
approximately 6 in. of line is showing on each side.
NOTE:
For best results, after every five to seven revolu-
tions of the SPEED WINDER
™
, pull both line ends taut for
best loading results and to help prevent line from tangling.
Push the bump knob down while pulling on line(s) to
manually advance the line.
CLEARING LINE JAM AND/OR REPLACING
BUMP KNOB
See Figures 9 - 10.
Stop the unit and disconnect the spark plug wire for gas
power heads, remove the battery pack for cordless power
heads, or disconnect from power supply for electric power
heads.
Depress the tabs on the side of the string head housing
to remove the lower string head housing.
NOTE:
The housing is spring loaded and will self eject
when the tabs are depressed. It is not necessary to re-
move the upper string head housing from the drive shaft.
Push the spool and bump knob through the string head
housing and remove the string from the spool.
If replacing the bump knob, remove the old knob from
the spool. Align the knob ribs with the spool slots and
place the new bump knob onto the spool. If you are not
replacing the bump knob, skip this step.
Insert the bump knob and spool assembly through the
opening in the string head housing.
Align the slots on the lower string head housing with the
tabs on the upper string head housing.
Push the housing together until the tabs snap into place.
NOTE:
Hold the spool by the knob while completing the
installation.
Install line as described in
Line replacement.
Summary of Contents for Expand-It RYSST44
Page 28: ...NOTES NOTAS...
Page 29: ...11 NOTES NOTAS...
