background image

11

OUT

IN

GRIP/REL

GR

IP/

RE

L

WARNING:

 

Do  not  allow  familiarity  with  tools  to  make  you  care-
less. Remember that a careless fraction of a second is 
sufficient to inflict serious injury.

WARNING:

 

Always wear safety goggles or safety glasses with side 
shields when operating tools. Failure to do so could re-
sult in objects being thrown into your eyes, resulting in 
possible serious injury.

WARNING:

Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result 
in serious personal injury.

APPLICATIONS

You may use this tool for the purpose listed below:

 

Removing/installing light bulbs

WARNING:

Battery tools are always in operating condition. There-
fore, switch should always be locked when not in use or 
carrying at your side.

WARNING:

Do not use EZ Reach on free hanging light fixtures. Only 
use on light sockets and fixtures that are fixed in place. 

The EZ Reach system can be used with or without an ex-
tension pole. To use without an extension pole, follow all 

Assembly

 instructions for the EZ Reach system, but do not 

attach the stick driver to a pole.

REMOVING/INSTALLING LIGHT BULB

See Figures 8 - 11.

 

Push the power button on the stick driver to turn on the 
driver. The green activation light should light up.

 

Slide the ON/OFF switch on the AIRgrip system to the 

ON

 

( I )

 position. The AIRgrip system will briefly vibrate 

when turned on.

NOTE:

 The power light on the AIRgrip system should be 

green. When the battery in the AIRgrip system is low, the 
power light will change from green to red. Change the bat-
tery immediately. Refer to 

Changing the Batteries

 later in 

this manual.

OPERATION

Fig. 8

Fig. 9

Fig. 10

POWER BUTTON

ON/OFF 

SWITCH

POWER LIGHT

GRIP/

REL

LIGHT 

BULB

SUCTION HEAD

Summary of Contents for AIRGRIP EZ REACH ELB001















Reviews: