background image

4

SPECIFIC SAFETY RULES

 

Do not use EZ Reach on a hot bulb. 

Turn off light switch 

and allow previously lit light bulb to cool.

 

Do not use EZ Reach on free hanging light fixtures. 

Only use on light sockets and fixtures that are fixed in 
place.

 

Remove all batteries from the power tool if you will 
not be using the power tool for an extended time.

 

Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well as 
the specific potential hazards related to this power 
tool. 

Following  this  rule  will  reduce  the  risk  of  electric 

shock, fire, or serious injury.

 

Battery tools do not have to be plugged into an elec-
trical outlet; therefore, they are always in operating 
condition.  Be  aware  of  possible  hazards  when  not 
using your battery tool or when changing accessories. 

Following this rule will reduce the risk of electric shock, 
fire, or serious personal injury.

 

Do not place battery tools or their batteries near fire 
or heat. 

This will reduce the risk of explosion and pos-

sibly injury.

 

Batteries vent hydrogen gas and can explode in the 
presence of a source of ignition, such as a pilot light. 

To reduce the risk of serious personal injury, never use 
any cordless product in the presence of open flame. An 
exploded  battery  can  propel  debris  and  chemicals.  If 
exposed, flush with water immediately.

 

Under  extreme  usage  or  temperature  conditions, 
battery leakage may occur. If liquid comes in contact 
with your skin, wash immediately with soap and water, 
then neutralize with lemon juice or vinegar. If liquid 
gets into your eyes, flush them with clean water for 
at least 10 minutes, then seek immediate medical at-
tention. 

Following this rule will reduce the risk of serious 

personal injury.

 

FCC Statement: 

This equipment generates, uses, and 

can radiate radio frequency energy and, if not installed 
and  used  according  to  the  instructions,  may  cause 
harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which is 
found by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or 
more of the following measures:

 

 

Reorient or relocate the receiving antenna.

 

 

Increase the separation between the equipment and 

the devices.

 

 

Consult  a  dealer  or  an  experienced radio/television 

technician for assistance.

   

If  more  than  one  unit  is  being  used  in  the  same 

location,  keep  a  minimum  distance  of  20 ft.  between 
the units.

Summary of Contents for AIRGRIP EZ REACH ELB001















Reviews: