background image

 

RUSH DC1 Aqua User Manual 

6

Respect all locally applicable laws, codes and regulations when 
installing, operating or servicing the fixture. 

There are no user-serviceable parts inside the fixture. Do not 
open it. Refer any service or repair operation not described in 
this manual to an authorized Martin™ service technician. Do not 
try to carry out any such operation yourself, as doing so may 
present a health or safety risk. It may also cause damage or 
malfunction and it may void your product warranty. 

 

Install, operate and service RUSH by Martin™ products only as 
directed in their user manuals, or you may create a safety 
hazard or cause damage that is not covered by product 
warranties. 

Follow the safety precautions listed below and observe all 
warnings in this manual and printed on the product. Keep this 
user manual for future use.  

For the latest user documentation and other information for this 
and all Martin™ products, please visit the Martin website at 
http://www.martin.com 

 

Protection from electric shock   

Do not expose the fixture to rain or moisture. 

Disconnect the fixture from AC power before carrying out any 
installation or maintenance work and when the fixture is not in 
use. 

Ensure that the fixture is electrically connected to ground (earth). 

Use only a source of AC power that complies with local building 
and electrical codes and has both overload and ground-fault 
(earth-fault) protection. 

Socket outlets or external power switches used to supply the 
fixture with power must be located near the fixture and easily 
accessible so that the fixture can easily be disconnected from 
power. 

Replace defective fuses with ones of the specified type and 
rating only. 

Isolate the fixture from power immediately if the power plug or 
any seal, cover, cable, or other component is damaged,  

Summary of Contents for DC 1 Aqua





































Reviews: