Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 91

Page: 91 / 123

Monitoring the Device

•

Interpreting port-side LEDs......................................................................................................................................91

•

Interpreting nonport-side LEDs................................................................................................................................98

•

Pinging an IP address..............................................................................................................................................98

•

Tracing a route........................................................................................................................................................ 98

•

Digital optical monitoring......................................................................................................................................... 99

•

Monitoring power and cooling................................................................................................................................. 99

Interpreting port-side LEDs

After you install the network cables, you can observe certain LEDs to determine if the network connections are functioning properly. The
tables in this section outline the state of each LED, the status of the hardware, and any recommended action.

FIGURE 61 Port-side LEDs of ICX 7150-C12P

Port status mode selection button

Port link status mode LED

Port speed status mode LED

Member ID status mode LED

USB status mode LED

PoE status mode LED

System Status LED

Master/Slave status LED

Software update status LED

10.

RJ-45 port 5 RX/TX activity LED (if blinking indicates RX/TX activity)

11.

PoE LED

12.

RJ-45 uplink port C1 status LED

13.

RJ-45 uplink port C1 RX/TX activity LED

14.

SFP+ uplink port X1 status LED (if blinking indicates RX/TX activity)

15.

SFP+ uplink port X2 status LED (if blinking indicates RX/TX activity)

16.

Power status LED

17.

Cloud management status LED (not currently enabled)

18.

Diagnostics status LED

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Summary of Contents for ICX 7150-24



























































































































Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands