Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 49

Page: 49 / 123

CAUTION
Ensure that adequate ventilation and airflow is provided for the system. A 4.5 cm (1.77 in) clearance is recommended above and
below the device and 8 cm (3.15 in) clearance is recommended on each side.

NOTE
You need a #2 Phillips screwdriver for rack mount installation.

NOTE
The ICX 7150-C12P compact device requires the ICX7000-C12-RMK rack mount kit which is optionally orderable.

Complete the following steps to mount devices in a rack.

1. Remove the rack mounting kit from the shipping carton. The kit contains two L-shaped mounting brackets and six sink-head

screws.

Mounting the Device

Mounting on a two-post rack

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Summary of Contents for ICX 7150-24



























































































































Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands