manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Share
Download
Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 76

6. After POST is complete, verify that the switch power and switch status LEDs are green.

NOTE
Power Supply LED should always display solid green to ensure a working power supply. If the LED is amber, it indicates
a faulty PSU.

For more information about how to interpret POST, BOOT, and diagnostics tests, refer to 

Monitoring the Device

 on page 91.

Establishing a first-time connection to the console

port

You can use either the USB Type-C console port or the RJ-45 serial console port to establish the first time connection to the device. The
console port allows you to configure and manage the device using a third-party terminal emulation application from a workstation that is
directly connected to the port using a standard USB Type-C cable or RJ-45 serial cable. Perform the following steps to log in to the device
for the first time through the console connection.

1. Do one of the following:

•

Connect a standard USB cable to the USB Type-C console connector on the device and to a USB port on the workstation.
To connect the USB Type-C console port on the device to a USB port on the workstation, you need a standard USB cable
that has a USB Type-C connector on one end and a USB connector on the other end that matches the USB port on your
workstation.

•

Connect a standard RJ-45 cable to the RJ-45 serial console connector on the device and to a USB port on the workstation.
To connect the RJ-45 serial console port on the device to a USB port on the workstation, you need a standard RJ-45 cable
that has a RJ-45 connector on one end and a USB connector on the other end that matches the USB port on your
workstation.

2. Allow the workstation to automatically discover and configure the newly found USB device.

NOTE
If the workstation is unable to automatically discover and configure the newly found USB device, you can manually
download the necessary device drivers for Windows, MacOS, and Linux from the following website: 

http://

my.brocade.com

Initial Setup and Verification
Establishing a first-time connection to the console port

Ruckus ICX 7150 Switch Hardware Installation Guide

76

Part Number: 53-1004928-05

Summary of Contents for ICX 7150-24




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands