Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 63

Page: 63 / 123

4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 40 Attaching the front brackets to the rear of the device

Brocade device

Front brackets

Screws, 8-32 x 5/16-in., flathead Phillips

Attaching the bracket extensions to the front of the device

Complete the following steps to attach the bracket extensions to the front of the device.

1. Position the right bracket extension along the side of the device as shown in

Figure 41

2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket extension and then into the holes on

the side of the device. Use the upper and lower screw holes, leaving the center holes empty.

3. Repeat step 1 and step 2 to attach the left front bracket extension to the left side of the device.

Mounting the Device

Flush-rear (recessed) mounting the device in the rack

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Summary of Contents for ICX 7150-24



























































































































Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands