RTA 460PSUSB-N70U Product User Manual Download Page 71

Page: 71 / 76

Fatal Error: Hardware Port Not Configured – The port selected on the ASCII Configuration page is not
configured.
a.

Verify the ASCII device is enabled and configured.

Verify the port configured matches the port enabled.

LED Status

- This is the Status for

All ASCII

or the specific ASCII device selected.

Solid Green (Connected) – The gateway is receiving/transmitting data within the Inactivity period for
all of the ASCII devices that are configured and enabled.

Flashing Green (Not Connected) – No messages have been received or transmitted.

Flashing Red (Connection Timeout) – The only way to get out of this state is with a valid received
message.
a.

Data has been discarded due to the queue being full.

Data has not been received/transmitted within the Inactivity period.

Variables

- These are the values for

All ASCII

or the ASCII device selected.

Successful Transmit Count:

-Number of Messages that the gateway has transmitted to the ASCII device

Successful Receive Count:

-Number of Complete Messages that the gateway has received from the ASCII device

Received due to Length:

-Number of Messages Completed due to the Max Message Length being reached

Received due to Delimiters:

-Number of Messages Completed due to the Start or End Delimiters being seen

Received due to Timeout:

-Number of Messages Completed due to the Receive Character Timeout being reached

Received but Discarded:

-Number of Messages that are Complete but discarded due to the Queue being full

-Change the Gateway Hold Msg Timeout to be less than what you currently have set

Successful Parsed Messages:

-Number of Messages that are Complete and have been successfully parsed

Failed Parsed Messages:

-Number of Messages that are Complete but have not been parsed successfully

Status Strings

These are the values for

All ASCII

or the ASCII device selected.

Queued Messages:

-The Gateway will hold up to 20 (configurable) complete messages to send to the other protocol

-This will only increment if the Gateway Hold Msg Timeout is non-zero and messages are being

received faster than we can send to the other protocol

Last Parsed Error:

-Last parsed error the gateway encountered

Common Error Messages:

Number of Fields Invalid:

The total number of parsed fields is greater than the number of fields the

gateway was expecting

Discard:

The Field has been discarded

Real Time Automation, Inc.

1-800-249-1612

Summary of Contents for 460PSUSB-N70U













































































Search results

Summary of Contents for 460PSUSB-N70U

Reviews:

Related manuals for 460PSUSB-N70U

Brands by name

Popular brands

RTA 460PSUSB-N70U, Product User Manual

Search results

Summary of Contents for 460PSUSB-N70U

Reviews:

Related manuals for 460PSUSB-N70U

Brands by name

Popular brands