RS SAILING RSCAT 14 Rigging Manual Download | Manualshive

Page: 25 / 65

background image

23

i)

Insert pin through mast step.

4.2 - Assembly - Mast

• Make sure you have lined up the up the holes on the bracket and mast, then attach it

using the 6 rivets provided.

Attaching the Masthead Float

The fixed masthead float must be fitted before stepping the mast in the boat.

• Attach the bracket to the masthead float using the four bolts provided.

h)

The brackets are not the same and are

labelled port and starboard. Make sure you

use the correct bracket on each side.

«
...
23
24
25
26
27
...
»

Summary of Contents for RSCAT 14


































































Reviews:

No comments

Related manuals for RSCAT 14

Brand: Pro-Line Boats Pages: 66

Brand: Walker Bay Pages: 13

Brand: Hallberg-Rassy Pages: 61

Brand: Hobie Pages: 28

Brand: Scout Boats Pages: 112

Brand: True Course Yachting Pages: 28

Brand: C&C Pages: 66

Brand: BENETEAU Pages: 164

Brand: Carver Yachts Pages: 135

Brand: Carver Yachts Pages: 126

WaveRunner VXS 2014

Brand: Yamaha Pages: 98

WaveRunner VXR 2018

Brand: Yamaha Pages: 108

Brand: BENETEAU Pages: 70

Brand: Yamaha Pages: 1

Brand: Yamaha Pages: 8

WaveRunner VX1800-N 2014

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 86

Brand: VFTech Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands