background image

UNIVERSAL TOASTER UTX-200L

4

P/N 1010992 Rev. K 03/15 

McDonald’s

Throughout this manual, you will find the following safety words and symbols that signify important safety 

issues with regards to operating or maintaining the equipment.

IMPORTANT SAFETY INFORMATION

In addition to the warnings and cautions in this manual, 

use the following guidelines for safe operation of the 

unit.

  •  Read all instructions before using equipment.
  •  For your safety, the equipment is furnished with 

a properly grounded cord connector.  Do NOT 

attempt to defeat the grounded connector.

  •  Install or locate the equipment only for its intend-

ed use as described in this manual.  Do NOT use 

corrosive chemicals in this equipment.

  •  Do NOT operate this equipment if it has a dam-

aged cord or plug, if it is not working properly, or 

if it has been damaged or dropped.

  •  This equipment should be serviced by qualified 

personnel only.  Contact the nearest Authorized 

Service Agency for adjustment or repair.

  •  Do NOT block or cover any openings on the unit.
  •  Do NOT immerse cord or plug in water.
  •  Keep cord away from heated surfaces.
  •  Do NOT allow cord to hang over edge of table or 

counter.

  •  Do NOT operate unit on a combustible counter 

top.

  •  Do NOT clean this appliance with a water jet.
The following warnings and cautions appear throughout 

this manual and should be carefully observed.

  •  Turn the power off, wait for the cool-down pro-

cedure to complete its cycle (45 minutes), and 

unplug the power cord before performing any ser-

vice or maintenance on the unit.

NOTE: Turning off the power switch does NOT turn 

off all power to the unit. When the unit is plugged 

in and turned off, an LED light will flash to indicate 

that the power cord is plugged in. 

  •  The procedures in this chapter may include 

the use of chemical products.  These chemical 

products will be highlighted with bold face let-

ters followed by the abbreviated 

HCS 

(Hazard 

Communication Standard).  See Hazard 

Communication Standard manual for the appro-

priated Material Safety Data Sheets (MSDS).

  •  The equipment should be grounded according to 

local electrical codes to prevent the possibility of 

electrical shock.  It requires a grounded recep-

tacle with separate electrical lines, protected by 

fuses or circuit breaker of the proper rating.

  •  Bread may burn.  Therefore toasters must not be 

used near or below curtains or other combustible 

walls and materials.  Failure to maintain safe 

operating distances may cause discoloration or 

combustion. 

 

    This equipotentiality symbol shows    

  external functional grounding connection.

WARNING

GENERAL WARNING.  Indicates information 

important to the proper operation of the equip-

ment.  Failure to observe may result in damage to 

the equipment, severe bodily injury or even death.

WARNING

ELECTRICAL WARNING.  Indicates information 

relating to possible shock hazard.  Failure to 

observe may result in damage to the equipment 

and/or severe bodily injury or death.

CAUTION

GENERAL CAUTION.  Indicates information impor-

tant to the proper operation of the equipment.  

Failure to observe may result in damage to the 

equipment.

WARNING

HOT SURFACE WARNING.  Indicates information 

important to the handling of equipment and parts.  

Failure to observe caution could result in personal 

injury.

WARNING

To avoid possible personal injury and/or dam-

age to the unit, all inspections, tests, and repair 

of electrical equipment should be performed 

by QUALIFIED SERVICE PERSONNEL. The unit 

MUST be shut down and UNPLUGGED before any 

internal servicing, except when electrical tests are 

required. Use extreme care during electrical cir-

cuit tests. Live circuits will be exposed.

Summary of Contents for 9210805





















Reviews: