background image

UNIVERSAL TOASTER UTX-200L

15

P/N 1010992 Rev. K 03/15 

McDonald’s

DAILY: Cleaning the Accessories, Release 

Sheet, and Vertical Conveyor Belt

NOTE: Do NOT wash accessories in the Power 

Soak machine.

CLEANING THE ACCESSORIES AND TOASTER

  1.  Turn the Power Switch off. The red light on the 

switch turns off (if present).

  2.  The unit enters cool down mode and displays  

OK to Clean

. The fans continue to run. This 

cool down mode continues for 45 minutes and 

shuts the unit down automatically when complete.

NOTE: You do NOT need to wait for the count down 

to complete. Continue with the cleaning steps as 

soon as you see 

OK to Clean

.

  3.  Wearing Heat Resistant Gloves, remove the  

following items from the unit (refer to Figure 1):

 

  •  Breakfast Chute (Rear of unit)

 

  •  Bun Feeder (Top of unit)

 

  •  Bun Buffer (Front of unit)

 

  •  Unit Crumb Tray (Rear of unit)

 

  •  Release Sheet Retainer Bar and Release  

  Sheet (Top of unit)

MAINTENANCE

WARNING

The unit will remain hot to the touch while it is 

cooling down. Personal injury and burns may 

result from touching the unit before it is finished 

cooling down. Wear Heat Resistant Gloves!

CLEANING THE RELEASE SHEET

  1.  Remove the Release Sheet from the Release 

Sheet Retainer Bar and inspect both sides of the 

Release sheet.

NOTE: Replace the Release Sheet if it is overly 

worn, creased, or torn.

  2.  Lay the release sheet on a clean, flat, dry sur-

face. Spray 

EXCEED Glass and Multi-Purpose 

Cleaner (HCS)

 on a clean, dry towel.

  3.  Wipe the Release Sheet firmly from top to bottom 

over its entire surface. 

  4.  Immediately repeat this procedure with a clean, 

dry towel dampened with water. 

  5.  Finally, wipe the entire Release Sheet with a clean 

towel dampened with 

KAYQUAT II™ Sanitizer 

Solution (HCS)

 and allow to air dry. 

  6.  Turn the Release Sheet over and repeat Steps 2 

through 5 on the reverse side.

CLEANING THE VERTICAL CONVEYOR BELT

NOTE: Wear Heat Resistant Neoprene Gloves.

  1.  Face the rear of the unit. Turn the two Back Panel 

Release Latches (Figure 8) to the vertical position 

and open the Back Panel. 

WARNING

Do NOT wash any of the accessories in a Power 

Soak Machine or any other mechanical washer. 

Damage to the accessories may result. Wash all 

accessories by hand in the sink.

  4.  Set the Release Sheet Retainer Bar and the 

Release Sheet aside.

  5.  Wash the Breakfast Chute, Bun Feeder, Bun 

Buffer, and Crumb Tray in the three compartment 

sink.

  6.  Wipe down the outside of the toaster with a clean, 

sanitized towel dampened with 

KAYQUAT II™ 

Sanitizer Solution (HCS)

.

WARNING

The Horizontal Conveyor Belt and the Vertical 

Conveyor Belt continue to turn during Cleaning 

mode. To stop the belts, press the UT button. To 

temporarily advance the belts during cleaning, 

press and hold both MUFFIN/BAGEL buttons as 

desired. Release to stop the belts again. Be sure 

to press UT again to resume. 

Summary of Contents for 9210805





















Reviews: