ROUND Pools AMBASSADOR Installation Manual Download Page 35

Page: 35 / 40

No Diving or Jumping.

Observe all Safety Rules.

4-3

3. Install the Top Rails-Round Section

a. Place a top rail (key 7) with one end on top of the top plate.

The side of the top rail facing the centre of the pool should be

close to the pool liner and pool wall. The side of the top rail

facing the

outside of the pool will form a large overhang.

b. Line up the holes as shown. Fasten through the

two oval holes into the holes marked

‘A‘

in the top plate

below with two self-tapping screws (key 8).

Do not

tighten

the screws yet. Leave the screws slightly loose until all the top

rails are in place.

c. Repeat the last two steps for the other end of the

top rail.

d. Repeat steps (a) to (c) to install

the rest of the top rails around

the top of the pool wall.

e. Make the pool settle into a perfect cir-

cle by pushing the top of the pool wall

vigorously

inward at each vertical

(this will help make the bottom of the

pool wall shift into a perfect circle).

f. Adjust all the top rails to line up

evenly with each other and tighten all

the screws.

Summary of Contents for AMBASSADOR









































Search results

Summary of Contents for AMBASSADOR

Reviews:

Related manuals for AMBASSADOR

Brands by name

Popular brands

ROUND Pools AMBASSADOR, Installation Manual

Search results

Summary of Contents for AMBASSADOR

Reviews:

Related manuals for AMBASSADOR

Brands by name

Popular brands