Ropox FlexiElectric 30-66-3 Series User Manual, Mounting Instructions Download Page 3

Page 3 

1. 

Introduction 

 

You have chosen Flexi, the multi-flexible, height-adjustable, easy-to-mount frame. The frame may 
be used separately or in combination with Diagonal or Verti, the adjustable system for wall 
cupboards. 
 
The frame has no inconvenient fascia and, consequently, the adjustment of the working height 
from 65 to 95 cm + worktop thickness may be fully utilised. 
Under the worktop there is sufficient room for knees and legs for wheelchair users, who obtain 
freedom of movement and a perfect working posture. 
 
If you want the colour of the frame to match your kitchen, you may order suitable covers for the 
vertical legs. 
 
The Flexi frame is delivered with electrical function. 
 
You have chosen the electrical version, and you will obtain a quick and easy adjustment of the 
frame by activating the control buttons. 
 
 
 
 
 

The correct use, operation and inspection are decisive factors for efficient and safe 
performance. 

 
 
 
 
 

 

2. 

Compliance with EU-Directives 

 

This product has CE-marking according to the current Machinery, EMC and Low Voltage Directives 
and thus complies with the basic safety requirements. See separate CE-declaration. See page 
277

 

If these table frames are assembled or otherwise connected with other electrical components, this 
will be considered a new unit. Consequently, the assembled unit must be subjected to a risk 
assessment, after which the CE mark may be awarded. 
 

3. 

Application 

 
The Flexi frame is adjustable in height in order to obtain optimum working height for user and 
helper. Do NOT use Flexi as a lifting table or person lifter.  
 
The product should be used indoor, at temperatures and humidity as described in section 4  
 

The control unit complies with IP32/ll and must always be installed in accordance with the 
national Heavy Current Regulations or corresponding national or international standards. 

 
 

This document must ALWAYS be kept with the product and have been read and 
understood by the user.  

 

If this product is electrically adjustable in height there is a risk of squeezing. The 
product must therefore always be operated by or under the guidance of an 
experienced adult, who has read and understood the importance of section 11 

”Safety 

in use”. 

 

Summary of Contents for FlexiElectric 30-66-3 Series





























Reviews: