Romac Transmate TapMate Operating Manual Download Page 28

Page: 28 / 35

TAPMATE

™

XL 424 OPERATING MANUAL

7 8 9

10 11

12 13

TAPMATE™ XL-424 (366-00)

Items included with Base Machine

REF

NO.

ITEM NUMBER

DESCRIPTION

366‑00

Base Machine (see following page for parts list)

366‑61

TM‑XL, STORAGE‑WORK STATION CRATE

366‑43

TM‑XL, LARGE ADAPTER HUB

366‑42

TM‑XL, SMALL ADAPTER HUB

366‑10

TM‑XL, LARGE SHAFT HEAD ASSEMBLY

366‑11

TM‑XL, SMALL SHAFT HEAD ASSEMBLY

350‑21‑A

TM,SHAFT NOSE COMPLETE

350‑04

TM,PVC PILOT

350‑14

TM,PILOT DRILL EXTENSION REQUIRED FOR 10 & 12 TAPS

366‑38‑2

TM‑XL, SHAFT NOSE, COMPLETE (14" ‑ 16")

366‑38

TM‑XL, SHAFT NOSE, COMPLETE (18" ‑ 24")

366‑39‑2

TM‑XL, PVC PILOT, COMPLETE (14" ‑ 16")

366‑39

TM‑XL, PVC PILOT, COMPLETE (18" ‑ 24")

350‑52

TM, JAM NUT (FOR CUTTERS)

353‑10‑1

B1, LUBRICANT, TECH‑LUBE TAPPING COMPOUND

366‑66‑10

TM‑XL, TOOL KIT & SPARE PARTS (items listed below, not pictured)

8FW‑410

WASHER,304SS, 5/8 IN.(4)

350‑05‑80.96‑52

TM,HUB ADAPTER NUTS (4)

350‑23‑512

TM,LEAD TUBE PRESSURE PLUG (3)

350‑05‑571

TM,ADAPTER BELL O‑RING

355‑60‑3

35,ALLEN WRENCH,1/8 IN.

353‑60‑31

B1,ALLEN WRENCH 3/16 IN

355‑60‑4

35, 12 IN. SPUD WRENCH

356‑01‑03

BT SLIDE GATE PIPE NIPPLE 1/2 IN. x,1‑1/2 IN.

360‑19

QVIM,ZIRC FITTING,1/8 IN.NPT STRAIGHT, PN 5000

935‑00090

PIPE PLUG,1/2‑14 NPT W/SQ HEAD

366‑66‑12

TM‑XL, ADJUSTABLE LIFTING CHAIN

366‑44

TM‑XL, ADAPTER HUB O‑RING, 2‑237, NITRILE

372‑08

HD HYDRAULIC COUPLING SET SCREW SHSS,1/4‑20 X 1/2 IN. (3)

366‑02‑10

TM‑XL, CUTTER BOLT, 5/8"‑11 X 1" HEX HEAD, ZINC (4)

366‑66‑09

TM‑XL, PIN STYLE ADJUSTABLE SPANNER WRENCH, 4‑1/2" ‑ 6‑1/4"

366‑66‑08

TM‑XL, 3/8 HEX BIT SOCKET X 6 IN LONG ‑ 1/2 SQ DRIVE

366‑66‑14

TM‑XL, ALLEN WRENCH, 5/32 IN.

366‑68

TM‑XL, ANTI‑SEIZE LUBRICATING COMPOUND SAMPLE, FASTORQ A/G

Operating Manual

Summary of Contents for Transmate TapMate




































Search results

Summary of Contents for Transmate TapMate

Reviews:

Related manuals for Transmate TapMate

Brands by name

Popular brands

Romac Transmate TapMate, Operating Manual

Search results

Summary of Contents for Transmate TapMate

Reviews:

Related manuals for Transmate TapMate

Brands by name

Popular brands