Romac Transmate TapMate Operating Manual Download Page 34

Page: 34 / 35

TAPMATE

™

XL 424 OPERATING MANUAL

TM-XL,SHAFT NOSE,COMPLETE

(18" - 24")

366-38

1) 360-22-03

2) 360-22-04

3) 360-22-02

4) 358-88-01

5) 362-06-03

QVIM,SHAFT NOSE RETAINING PIN SET SCREW

QVIM,SHAFT NOSE RETAINING PIN SPRING

QVIM,SHAFT NOSE RETAINING PIN

IVS, SPADE BIT 1 3/8 IN. FOR SHAFT NOSE

QVR,6 REAMER CLAMP SCREW,

QTY 3

QTY 1

3
2
1

QTY 2

QTY 1

366-38

TM-XL,SHAFT NOSE, COMPLETE

(14" - 16")

366-38-2

366-38-2

350-21-512

TM, COUPON RETAINER SET SCREW

3/8-24 x 3/8 SHSS, CUP POINT

350-21-55

TM, COUPON RETAINER SPRING

350-21-561

TM, COUPON RETAINER BALL, 5/16

350-03-531

TM, SPADE BIT LOCK SCREW

10-24 x 3/4 IN. LONG S.H.C.S.

350-03-08

TM, PILOT SPADE BIT 1 IN.

TM, SHAFT NOSE

TM,SHAFT NOSE COMPLETE

350-21-A

Summary of Contents for Transmate TapMate




































Search results

Summary of Contents for Transmate TapMate

Reviews:

Related manuals for Transmate TapMate

Brands by name

Popular brands

Romac Transmate TapMate, Operating Manual

Search results

Summary of Contents for Transmate TapMate

Reviews:

Related manuals for Transmate TapMate

Brands by name

Popular brands