rollease acmeda Automate Rechargeable Motorization Programming Instructions Manual Download Page 10

Page: 10 / 10

The speed at which the shade moves can be increased or decreased.

If the motor does not react to the speed adjustment, the maximum or minimum speed has already been reached.

NOTE:

Adjusting motor speed can only be done with a single channel or 15 channel remote.

It cannot be adjusted/set with the wall switch.

ADVANCED PROGRAMMING

ADJUSTING MOTOR SPEED

1. Press the

button on the back of the remote. The shade will jog once followed by a beep.

NCReASING

mOTOR

SPeed

2. Press the

button. The shade will jog once then been once.

3. After the beep, press the

button again. The shade will jog twice then beep once.

This confirms the speed has been increased.

If the speed needs to be increased more, repeat the steps above.

1. Press the

button on the back of the remote. The shade will jog once

followed by a beep.

eCReASING

mOTOR

SPeed

2. Press the

DOWN

button. The shade will jog once then beep once.

3. After the beep, press the

DOWN

button again. The shade will jog twice then beep once.

This confirms the speed has been decreased.

If the speed needs to be decreased more, repeat the steps above.

The 15 channel remote can be programmed to have anywhere from 1 to 15 channels visible.

The inactive channels will not be visible while scrolling through channel selection.

HIDE UNUSED CHANNELS

NOTE:

If a channel is removed while a shade is still linked to it, that shade will still operate when “0” is

selected. If the channel is brought back, then the shade will still be linked to that channel.

1. Hold the

STOP

and

CHANNEL

buttons at the same time. The number “15” will flash on the

screen, and both directional indicators will appear.

NOTE:

The

CHANNEL

button must be held during this entire process.

2. While holding the

CHANNEL

button, use the

and

DOWN

buttons to select the desired

number of visible channels.

3. Still holding the

CHANNEL

button, press the

STOP

button to confirm the amount of

channels. Once the

STOP

button is pressed, both directional indicators will disappear, and

both buttons can be released.

The new channel total will flash for a few seconds. Once the flashing stops the remote is ready to use.

Follow these same steps to make removed channels visible again.

STOP

Down

Summary of Contents for Automate Rechargeable Motorization











Search results

Summary of Contents for Automate Rechargeable Motorization

Reviews:

Related manuals for Automate Rechargeable Motorization

Brands by name

Popular brands

rollease acmeda Automate Rechargeable Motorization, Programming Instructions Manual

Search results

Summary of Contents for Automate Rechargeable Motorization

Reviews:

Related manuals for Automate Rechargeable Motorization

Brands by name

Popular brands