Roland XS-82H, Reference Manual

Page: 7 / 24

Menu List
7
AUDIO INPUT
(continued)
Menu item
Value Description
2nd level 3rd level
ANALOG-1
ANALOG-2 PHANTOM POWER OFF, ON
This sets phantom power on or off (R channel only).
INPUT GAIN 0 dB–64 dB
This adjusts the input sensitivity (R channel only).
MONO INPUT
OFF, ON
Setting this to “ON” enables monaural input.
ANALOG-1
:
ANALOG-8
HPF OFF, ON
This sets the high-pass filter on or off. Setting this to “ON” attenuates the low band
while passing the high band unchanged.
HDMI-1
:
HDMI-8
ANALOG-1
:
ANALOG-8 4BAND EQUALIZER
OFF, ON
This sets the equalizer on or off.
HIGH GAIN -15 dB–0 dB–15 dB This boosts or attenuates the high band.
HIGH FREQ 600 Hz–8.00 kHz–12.0 kHz This adjusts the center frequency when changing the sound quality in the high band.
HI-MID GAIN
-15 dB–0 dB–15 dB This boosts or attenuates the high-midrange band.
HI-MID FREQ 20.0 Hz–2.50 kHz–10.0 kHz
This adjusts the center frequency when changing the sound quality in the high-
midrange band.
HI-MID Q 0.50–1.00–16.0 This adjusts the bandwidth when boosting or attenuating the high-midrange band.
LOW-MID GAIN -15 dB–0 dB–15 dB This boosts or attenuates the low-midrange band.
LOW-MID FREQ 20.0 Hz–2.50 kHz–10.0 kHz
This adjusts the center frequency when changing the sound quality in the low-
midrange band.
LOW-MID Q
0.50–1.00–16.0 This adjusts the bandwidth when boosting or attenuating the low-midrange band.
LOW GAIN
-15 dB–0 dB–15 dB This boosts or attenuates the low band.
LOW FREQ
50.0 Hz–112 Hz–800 Hz This adjusts the center frequency when changing the sound quality in the low band.
GATE OFF, ON
This sets gate on or off.
THRESHOLD -50 dB– -48 dB–0 dB
This sets the level used as the threshold for removing audio. Audio that does not reach
the threshold level is removed.
RELEASE 30 ms–500 ms–5000 ms
This adjusts the length of time until the gate effect ends after audio falls below the
threshold.
COMPRESSOR/
DUCKING
OFF, COMPRESSOR, DUCKING This sets the compressor or ducking on or off.
THRESHOLD -50 dB– -16 dB–0 dB
This sets the level used as the threshold when performing audio compression
(compressor) or attenuation (ducking).
Compressor: Compression is applied to audio that exceeds the threshold level.
Ducking: Audio that exceeds the threshold level is attenuated.
COMP-RATIO
1.0: 1, 1.2: 1,. 1.5: 1, 2.0: 1, 2.8: 1, 4.0: 1,
8.0: 1, 16: 1, INF: 1 This specifies the degree of compression applied to the audio. The state in which no
compression is applied is defined as “1.”
COMP-ATTACK 0.2 ms–50 ms–100 ms
This sets the time until the compression effect peaks after audio exceeding the
threshold is input.
COMP-KNEE
HARD, SOFT1–SOFT9
This adjusts the way in which the compressor is applied to the region near the
threshold level within a range extending from steep (HARD) to gentle (SOFT9).
COMP-RELEASE 30 ms–500 ms–5000 ms
This adjusts the length of time until compression ends after audio falls below the
threshold.
DUCK-KEY IN
SELECT
HDMI INPUT1–8, ANALOG INPUT1–8
* Default values differ according to input
channel.
This sets the channel to use as the key-in signal.
DUCK-ATTACK 0.2 ms–50 ms–100 ms
This sets the time until the ducking effect peaks after audio exceeding the threshold is
input.
DUCK-RELEASE 30 ms–500 ms–5000 ms
This adjusts the time until the ducking effect disappears after the time set for “DUCK-
HOLD” has passed.
DUCK-HOLD 0 ms–250 ms–5000 ms
This adjusts the length of time until the ducking effect starts to end after audio falls
below the threshold.
OUT1 SEND RATE
:
OUT4 SEND RATE
* This varies according
to model.
0 %–100 % This sets the audio send level for the respective output channel.