61
T-slot (XY) table size
Max. cuttng area
XYZ motor
Feed rate
Acceleration
Software resolution
Mechanical resolution
Spindle motor
Revolution speed
Tool chuck
Positioning accuracy
Repeat accuracy
Origin-point reproducibility
(when the power is switched on/off)
Possible table load weight
Interface
Buffer size
Instruction system
Control keys
Power consumption
Dimensions
Weight
Packed dimensions
Packed weight
Operation temperature
Operation humidity
Accessories
MDX-500
550 mm x 360 mm (21-5/8 x 14-1/8 in.)
500 mm(X) x 330 mm(Y) x 105 mm(Z) ( 19-5/8(X) x 12-15/16(Y) x 4-1/8(Z) in.)
AC servo motor
X, Y, Z-axis: Max. 85 mm/sec. (3-3/8 in./sec.)
0.3G, 0.1G, 0.05G
[When RML-1 has been selected]
0.01 mm/step (0.00039 in.)
[When NC codes has been selected]
0.001 mm/step (0.000039 in.)
Note that the measurement unit for positioning coordinates is 0.01 mm/step (0.00039 in.).
0.001 mm/step
DC brushless motor Max. 400W (when with high-torque spindle)
[High torque spindle] 3000 to 12000 rpm [High speed spindle] 5000 to 20000 rpm
(Variable manually or by the command set)
Collet or Cutter holder system
±
0.1 mm (0.00394 in.) / 300 mm (11-13/16 in.) (Under no-load conditions)
±
0.05 mm (0.00197 in.) (Under no-load conditions)
±
0.08 mm (0.00315 in.)
[0.3G] 12 kg (26.5 lb.) or less [0.05G] 15 kg (33.1 lb.) or less
Parallel (in compliance with the specification of Centronics)
Serial (under RS-232C standard)
2 Mbyte
( Replot buffer: [RML-1] 2 Mbyte [NC codes] Max. 2 Mbyte (end-user setting) )
RML-1 (mode1, mode2) or NC codes supported by the MDX-500 (Selectable through display operation)
COPY, XY, Z, +Z(Tool up), -Z(Tool down), PAUSE, SPINDLE, , ,
,
, FAST FEED, JOG
EXIT, ENTER, Dial, EMERGENCY STOP switch
6.5 A / 117 V 3.5 A / 220 to 230 V 3.5 A / 230 to 240 V
742 mm(W) x 843 mm(D) x 713 mm(H) (29-1/4(W) x 33-1/4(D) x 28-1/8(H) in.)
92 kg (202.8 lb.)
900 mm(W) x 970 mm(D) x 930 mm(H) (35-7/16(W) x 38-1/4(D) x 36-5/8(H) in.)
117 Kg (257.9 lb.)
5 to 40
°
C (41 to 104
°
F)
35 to 80% (no condensation)
T-slot clamps, Bolts (5 x 25 mm), Spanner (10 mm(3/8 in.)), Z0position sensor, Belt for high-torque spindle, Key
connector, Hexagonal wrench, User's manuals, CD-ROM, Power cord
MDX-500 Main Unit
Part 3 Appendix
Summary of Contents for MODELA Pro MDX-500
