Rohde & Schwarz 1145.5850.03 Operating Manual Download Page 3

Page: 3 / 245

R&S FSH

Contents

1145.5973.12 I.1

E-11

Contents

Specifications
Safety Instructions
Certificate of Quality
EC-Certificate of Conformity
Support Center Address
List of R&S Representatives

Putting into Operation

..............................................................................................................1.1

Front view

.........................................................................................................................................1.1

Putting into Operation

.....................................................................................................................1.2

Unpacking the Instrument...........................................................................................................1.2

Setting up the Instrument ...........................................................................................................1.3

Switching on the Spectrum Analyzer..........................................................................................1.4

Spectrum Analyzer Connectors..................................................................................................1.5

Screen Settings ..........................................................................................................................1.7

Country-Specific Settings ...........................................................................................................1.9

Setting the Date and Time ....................................................................................................... 1.10

Setting the date........................................................................................................... 1.10

Setting the time ........................................................................................................... 1.10

Charging the Battery

..................................................................................................................... 1.11

Selecting the Instrument Default Setup

...................................................................................... 1.12

External Reference / External Trigger Switchover

..................................................................... 1.13

Controlling the RF Attenuator

...................................................................................................... 1.14

Using a Preamplifier

...................................................................................................................... 1.14

PIN Entry

........................................................................................................................................ 1.16

Connecting Printers

...................................................................................................................... 1.18

Setting the Baud Rate for Remote Control

................................................................................. 1.20

Enabling Options

........................................................................................................................... 1.20

Checking the Installed Options

................................................................................................... 1.21

Summary of Contents for 1145.5850.03






















































































































































































































































Search results

Summary of Contents for 1145.5850.03

Reviews:

Brands by name

Popular brands

Rohde & Schwarz 1145.5850.03, Operating Manual

Search results

Summary of Contents for 1145.5850.03

Reviews:

Brands by name

Popular brands