background image

 

 

 

 

6.5 Power supply (230VAC) control 

PR821-CH  offers  functionalities which enable  230VAC  power  supply activation and  deactivation in 
hotel room. The power supply is not switched directly by the controller and it is necessary to use 

external relay for that purpose. The output connected to the relay e.g. IO1 must be assigned with 
the function 

[48]:POWER SUPPLY

. The example of 230VAC power supply control is shown in 

fig. 10. 

Caution!: In case of installation with  230VAC voltage, adequate safety measures must be applied 
and all works can be executed only by qualified and certified personnel. 

 

Fig. 10 Power supply (230VAC) controlled by PR821-CH controller 

In the standard scenario it is assumed that 230VAC power supply shall be activated by authorized 

user  card  i.e.  by  means  of  CARD  IN  HOLDER  flag  which  activates  POWER  SUPPLY  flag  and 
successively the output with the function 

[48]

. In such case 230VAC supply is available in room as 

long as card is in the holder plus time configured with POWER SUPPLY – SWITCH OFF DELAY timer 
in controller properties in 

Timers

 tab. By default, hotel staff user i.e. NORMAL user with 

Hotel 

staff

 attribute as well as guest user can activate CARD IN HOLDER flag in room with their cards. 

However it is also possible that any user card or any EM125kHz or Mifare card could  activate the 
flag  and  successively  switch  230VAC  power  supply  on.  This  can  be  configured  with  the  option 

CARD  IN  HOLDER  flag  switched  by

  in  controller  properties  in 

Hotel  options

  tab. 

Additionally it is also possible to switch the supply remotely from PR Master software using POWER 

SUPPLY flag but such method has lower priority than switching with card. 

6.6 Air conditioning control 

PR821-CH  offers  functionalities  which  enable  air  conditioning  control  in  hotel  room.  For  that 
purpose one of controller  outputs with the function 

[41]:AIR CONDITION

 can be used. AIR 

CONDITION flag and associated output 

[41]

 can be activated in several ways according to table 5. 

In  standard  scenario  of  operation  it  is  assumed  that  air  conditioning  shall  be  activated  with 
authorized user card i.e. by means of CARD IN HOLDER flag which activates AIR CONDITION flag 
and successively the output with the function 

[41]

. By default, hotel staff user i.e. NORMAL user 

with 

Hotel staff

 attribute as well as guest user can activate CARD IN HOLDER flag in room with 

Summary of Contents for PR821-CH






























Reviews: