background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

17/20 

 

Block ID 

Parameter defines block number where  PCN is stored. Range: 0-2 to 
for sectors 0-31 and 0-14 for sectors 32-39. Default value: 0. 

Key type 

Parameter  defines  key  type  used  to  access  sector  with  PCN.  Range: 
[0]: A, [1]: B, [2]: Roger. Default value: [0]: A. 

Key 

Parameter  defines  6  bytes  (12  HEX  digits)  key  for  accessing  sector 
where PCN is stored. 

Programmable card number (PCN) settings for Mifare Plus 

Sector type 

Parameter  defines  sector  type  with  programmable  number  (PCN).  If 
the  option  [0]:None  is  selected  then  card  returned  number  (RCN)  will 
include  only  CSN  and  PCN  will  be  discarded.  Range:  [0]:  None,  [1]: 
SSN, [2]: MAD. Default value: [0]: None. 

Format 

Parameter  defines  format  of  PCN.  Range:  [0]:  BIN,  [1]:  ASCII  HEX. 
Default value: [0]: BIN. 

First byte position (FBP) 

Parameter  defines  the  position  of  the  first  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 0. 

Last byte position (LBP) 

Parameter  defines  the  position  of  the  last  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 7. 

Sector ID 

Parameter defines sector number where PCN  is stored. Range: 0-39. 
Default value: 1. 

Application ID (AID) 

Parameter defines application ID number (AID) which indicates sector 
where PCN number is stored. Range: 0-9999. Default value: 5156. 

Block ID 

Parameter defines block number where  PCN is stored. Range: 0-2 to 
for sectors 0-31 and 0-14 for sectors 32-39. Default value: 0. 

Key type 

Parameter  defines  key  type  used  to  access  sector  with  PCN.  Range: 
[0]: A, [1]: B. Default value: [0]: A. 

Programmable card number (PCN) settings for Mifare Desfire 

Sector type 

Parameter  defines  sector  type  with  programmable  number  (PCN).  If 
the  option  [0]:None  is  selected  then  card  returned  number  (RCN)  will 
include  only  CSN  and  PCN  will  be  discarded.  Range:  [0]:  None,  [1]: 
Desfire file. Default value: [0]: None. 

Format 

Parameter  defines  format  of  PCN.  Range:  [0]:  BIN,  [1]:  ASCII  HEX. 
Default value: [0]: BIN. 

First byte position (FBP) 

Parameter  defines  the  position  of  the  first  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 0. 

Last byte position (LBP) 

Parameter  defines  the  position  of  the  last  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 7. 

Application ID (AID) 

Parameter defines application ID number (AID) which indicates sector 
where PCN number is stored. Range: 0-9999. Default value: F51560. 

File ID (FID) 

Parameter  defines  file  identifier  in  AID.  Range:  0-32  for  Desfire  EV1 
and 0-16 for Desfire EV0. Default value: 0. 

Communication protection level 

Parameter  defines  encryption  method  for  communication  between 
card  and  reader.  Range:  [0]:  Plain,  [1]:  Data  authentication  by  MAC, 
[2]: Full encryption. Default value: [0]: Plain. 

Key number 

Parameter  defines  application  key  number  used  for  file  read.  Range: 
0-13. Default value: 0. 

Key type 

Parameter  defines  encryption  key  type  for  Desfire  file.  Range:  [0]: 
TDES Native, [1]: TDES Standard, [2]: 3-KTDES, [3]: AES128. Default 
value: [0]: TDES Native. 

Summary of Contents for MCT88M-IO





















Reviews: