background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

9/20 

 

  PINs 

  Mobile devices (NFC and BLE) 

MIFARE cards 

By default the terminal reads serial numbers (CSN) of MIFARE cards but it is possible to program cards with 
own  numbers  (PCN)  in  selected  and  encrypted  sectors  of  card  memory.  The  use  of  PCN  prevents  card 
cloning and consequently it significantly increases security in the system. More information on MIFARE card 
programming is given in AN024 application note which is available at 

www.roger.pl

. 

PINs 

The terminal accepts variable length PINs (by default 4-8 digits). 

Mobile devices (NFC and BLE) 

The  terminal  MCT88M-IO  enables  user  identification  with  mobile  device  (Android,  iOS)  using  NFC  or 
Bluetooth  (BLE)  communication. Prior  to use  of  BLE/NFC  identification  on  the  terminal,  within  its  low  level 
configuration  (see  section  4)  configure  own 

NFC/BLE  authentication  factor  encryption  key

  and 

NFC/BLE 

communication encryption key

 while in case of Bluetooth additionally verify if the parameter 

BLE activated

 is 

enabled.  Install  Roger  Mobile  Key  (RMK)  app  on  mobile  device  and  configure  the  same  parameters  as  in 
the terminal. Create key (authentication factor) in RMK defining its type and number, then create the same 
authentication  factor  in  VISO  software  (fig.  13)  and  assign  it  to  the  user  with  adequate  Authorisation(s)  at 
the terminal. When user wants to identify at the terminal using mobile device then key (authentication factor) 
can be selected from the screen or with gesture. 
 

 

Fig. 13 Authentication factor type in VISO software 

Summary of Contents for MCT88M-IO





















Reviews: