background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

18/20 

 

Key 

Parameter defines access key for Desfire file with PCN. 3-KTDES key 
is  24  bytes  (48  HEX  digits),  TDES  and  AES  keys  are  16  bytes  (32 
HEX digits).  

 

Manual addressing 

Manual  addressing  procedure  enables  configuration  of  new  RS485  address  with  all  other  settings 
unchanged. 
 
Manual addressing procedure: 

1.  Remove all connections from A and B lines. 
2.  Place jumper on MEM contacts (fig. 15). 
3.  Restart the device (switch power supply off and on). The terminal will display CONFIG MODE text and 

orange LED SYSTEM will pulsate. 

4.  Enter 3 digits of RS485 address in range of 100-115 with keypad. 
5.  Wait till device starts to emit continuous sound. 
6.  Remove jumper from MEM contacts and restart the device. 

Memory reset procedure 

Memory reset procedure resets all settings to factory default ones including ID=100 address. 
 
Memory reset procedure: 

1.  Remove all connections from A and B lines. 
2.  Place jumper on MEM contacts (fig. 15). 
3.  Restart the device (switch power supply off and on). The terminal will display CONFIG MODE text and 

orange LED SYSTEM will pulsate. 

4.  Read any MIFARE card 11 times. 
5.  Wait till device confirms reset with continuous sound. 
6.  Remove jumper from MEM contacts and restart the device. 

High level configuration (VISO) 

The purpose of high level configuration is to define logical functioning of the terminal which communicates 
with  the  MC16  access  controller  and  it  depends  on  applied  scenario  of  operation. The  example  of  access 
control system configuration is given in AN006 application notes which is available a

www.roger.pl

. 

5.

 

F

IRMWARE UPDATE

 

New firmware can be uploaded to the terminal by means of included memory card. The latest firmware file is 
available a

www.roger.pl

. 

 
Firmware update procedure: 

1.  Disconnect power supply. 
2.  Press and remove memory card from socket (fig. 15). 
3.  Using  memory  card  reader,  copy  main  firmware  (*.frg)  to  the  card  and  rename  it  as  FW.BUF.  Copy 

additional firmware (*.cyacd) for keypad and BLE and rename it as KBDFW.CYA. 

4.  Insert the card into socket. 
5.  Connect  power  supply  and  wait  till  device  completes  starting  procedure.  The  progress  of  additional 

firmware uploading is shown on the display. 

6.  Disconnect power supply when additional firmware KBD is 100% uploaded. 
7.  Connect power supply and wait till device completes starting procedure. 
8.  Start RogerVDM and perform low level configuration. 

Note: During the firmware update process, it is necessary to ensure continuous and stable power supply for 
the device. If interrupted the device may require repair by Roger. 

Summary of Contents for MCT88M-IO





















Reviews: