background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

11/20 

 

NC 

REL relay output (NC) 

COM 

REL relay common terminal 

RS485 bus, line B 

RS485 bus, line A 

GND 

Ground 

+12V 

12VDC power supply 

1,2,3,4,5,6,7,8 

Ethernet port 

 
 

 

Fig. 16 Back panel 

Installation guidelines 

  The  terminal  should  be  mounted  on  a  vertical  structure  (wall)  away  from  sources  of  heat  and 

moisture. 

  The  back  panel  should  be  mounted  with  included  screws  according  to  fig.  16  in  such  way  as  the 

tamper lever would firmly press the tamper switch. 

  All electrical connections should be done with disconnected power supply. 

  If  the  terminal  and  controller  are  not  supplied  from  the  same  PSU  then  GND  terminals  of  both 

devices must be connected with any wire. 

  Clean  front  panel  regularly  by  means  of  wet  cloth  and  mild  detergent.  Do  not  clean  by  means  of 

abrasive materials and strong cleaners like alcohols, solvents, etc. Damages to screen surface are 
beyond the scope of warranty. 

3.

 

O

PERATION SCENARIOS

 

Access, T&A and building automation terminal 

The  MCT88M-IO  terminal  when  connected  to  MC16  access  controller  can  be  at  the  same  time  used  for 
access  control,  Time&Attendance  and  building  automation  functionalities.  The  example  of  connection 
diagram  for  such  scenario  is  shown  in  fig.  17  where  the  terminal

’s  power  supply  line  and  RS485  bus  are 

connected  directly  to  the  controller  and  relay  outputs  of  MCX8  expander  are  used  to  control  building 
automation.  Alternatively  the  communication  with  MC16  access  controller  can  be  provided  via  MCX16-RS 
expander (fig. 3). The terminal can also operate with MC16 controller using MCX2D/MCX4D expanders as 
in case of M16-PAC-x-KIT series. 
 

Summary of Contents for MCT88M-IO





















Reviews: