background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

2/20 

 

1.

 

D

ESIGN AND APPLICATION

 

The MCT88M-IO is an access terminal dedicated to RACS 5 system. The terminal is equipped with colour 
graphic  display,  sensor  type  keypad,  4  function  keys  and  MIFARE  Ultralight/Classic/DESFire/Plus/  reader. 
Users can identify  at the  terminal  with  PINs, MIFARE  cards and mobile devices  equipped  with NFC (Near 
Field Communication) or BLE (Bluetooth Low Energy) technology. MCT88M-IO can be connected to RS485 
bus  of  MC16  access  controller  directly  or  via  MCX16-RS  expander  using  Ethernet  network  (LAN). 
Alternatively  the  terminal  can  be  connected  to  virtual  controller  through  Ethernet  network  (LAN).  When 
connected to MC16 controller it can be operated as access control terminal, Time&Attendance terminal and 
additionally  it  can  be  used  to  control  the  system  especially  in  regard  of  building  automation  functionalities 
offered by RACS 5. When connected to virtual controller it can be operated as POS (Point of Sale) terminal 
or assets management terminal. 

Characteristics 

  RACS 5 system access terminal 

  MIFARE Ultralight/Classic/DESFire/Plus cards reader 

  NFC and BLE mobile device identification 

  Colour graphic display 

  Touch keypad 

  4 function keys 

  3 parametric (EOL) inputs 

  2 transistor outputs 

  1 relay output 

  RS485 interface 

  Ethernet (LAN) interface 

  Dimensions: 155,5 x 85,0 21,5 

Power supply 

The terminal requires power supply voltage in range of 11-15VDC. It can be supplied from the MC16 access 
controller  (e.g.  TML  output),  from  MCX2D/MCX4D  expander  or  from  dedicated  power  supply  unit.  The 
supply  wire  diameter  must  be  selected  in  such  way  that  the  voltage  drop  between  supply  output  and  the 
device would be lower than 1V. The proper wire diameter is especially critical when device is located in long 
distance from the supply source. In such a case the use of dedicated power supply unit located close to the 
device should be considered. When separate power supply unit is used then its minus should be connected 
to  controller’s  GND  by  means  of  signal  wire  with  any  diameter.  It  is  recommended  to  use  UTP  cable  for 
connection  of  device  to  controller.  The  table  below  shows  maximal  UTP  cable  lengths  in  relation  to  the 
number of wires used for power supply. 
 

Table 1. Power supply cabling 

Number of UTP wire pairs for power supply 

Maximal length of power supply cable 

150m 

300m 

450m 

600m 

 

Summary of Contents for MCT88M-IO





















Reviews: