Rocom Doortello Business FW T2.05W2.04 User Manual Download Page 13 | Manualshive

Page: 13 / 60

background image

User guide

Doortello Business

Issue 1.00

Page 13

Loudspeaker volume

Microphone volume

Doortello Business volume adjustment

First activation

Install and configure the door station as you wish. Ensure that you follow the

instructions of the single modules for a correct installation. Connect the module

together with the delivered flat cable, if needed. Select the correct addressing of

the module as described. After this you can connect the door phone with the

telephone line and the external power supply.

External power supply

- Connect FIRST the telephone line and then the external power supply.

Please note!

The external power supply voltage MUST NOT BE HIGHER THEN 12 Vdc! Check

the voltage using a voltmeter! A higher voltage may seriously damage the

device voiding you warranty! We suggest the use of out PRS 231S power

supply unit.

Please note!

You need a separate power supply unit for each door phone you are going to

install!

Please note!

The connector I/L doesn’t have a polarity. You can c/-as you wish.

- After you switch on the power supply the unit will follow an internal start up

procedure. This may take some seconds. If you have a module with LED (like the

«
...
11
12
13
14
15
...
»

Summary of Contents for Doortello Business FW T2.05W2.04





























































Reviews:

No comments

Related manuals for Doortello Business FW T2.05W2.04

Brand: Zenith Pages: 24

Brand: National Instruments Pages: 23

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: AMX Pages: 88

Brand: Digital Acoustics Pages: 14

Brand: Vonyx Pages: 16

Brand: The Fisher Pages: 20

Brand: Gardeners Pages: 2

Brand: Nakamichi Pages: 12

Brand: Detection Systems Pages: 2

Brand: Commax Pages: 15

Brand: Exibel Pages: 5

Brand: Korg Pages: 6

Brand: Metra Electronics Pages: 8

Brand: National Instruments Pages: 77

Brand: FARFISA INTERCOMS Pages: 11

Brand: Teac Pages: 23

Phontech CIS 3100

Brand: Zenitel Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands