manualshive.com logo in svg

Rockwell Automation Samsung NX-CPU700p, User Manual, Page: 84 / 122

Share
Download
Rockwell Automation Samsung NX-CPU700p User Manual Download Page 84

84

Output module

Symptom

Possible cause

Action

No outputs on an output module 
will turn On.

No external input power

Supply power

Low external input voltage

Supply rated load power 

Loose terminal screw or defective 
contact

Tighten the screw and reconnect 
the module

Defective I/O connector contacts

Replace the output module

Defective output circuit

Reconnect the output module

No outputs on an output module 
will turn Off.

Defective output circuit

Replace the output module

One or more inputs on an I/O 
module will not change to On state 
(LED is illuminated).

Output time too short

Correct the program

Defective output circuit

Replace the output module 

One or more inputs on an I/O 
module will not change to On state 
(LED is not illuminated).

Incorrect output load

Replace the output load

Short output wiring

Reconnect the output wiring

Loose terminal screw or defective 
contact 

Tighten screw and reconnect the 
module

Defective output contact 

Replace the output module or relay 

Defective output circuit

Replace the output module 

One or more outputs on an I/O 
module will not change to On state 
(LED is illuminated).

Defective output circuit

Replace the output module or relay

Error caused by leak or residual 
current

Replace the external load 

One or more outputs on an I/O 
module will not turn Off (LED is not 
illuminated).

Defective output circuit

Replace the output module

Output changes On/Off state 
erratically.

Low external input voltage

Supply rated load power

Noise error 

Countermeasure against noise 

Loose terminal screw or defective 
contact 

Tighten the screw and reconnect 
the module

A set of 8 points on an I/O module 
operate incorrectly or identically. 

Loose common terminal screw 

Tighten the screw and reconnect 
the module

Defective terminal connector

Tighten the screw and reconnect 
the module

CPU module error 

Replace the CPU module

Output display LED is not 
illuminated.

LED error

Replace the output module

Summary of Contents for Samsung NX-CPU700p



























































































































Reviews:

No comments