Rockwell Automation Samsung NX-CPU700p User Manual Download Page 6

Page: 6 / 122

ATTENTION

Electrostatic Discharges

Under dry condition, excessive electrostatic discharges
may occur. Make sure to remove electrostatic
discharges by touching a grounded metal piece before
touching your controller system modules.

ATTENTION

Cleaning

Never use chemicals such as thinner because they melt,
deform or discolor PCB boards.

ATTENTION

Precautions for use of power

• Run your PLC system only after the I/O devices and

motor devices have started. (For example, first power
on in the PROG mode, then change the operation
mode to RUN.)

• Make sure to power off I/O devices after ensuring PLC

operation is stopped.

• If you power on/off I/O devices when the PLC system

is in operation, the system may malfunction because
input signal noises may be recognized as normal
inputs.

ATTENTION

Before powering on

Make sure to follow these directions before powering
on your PLC system.

• When installing the system, ensure that there are no

metal chips or conductive fragments that stick to
wiring cables.

• Ensure that power supply and I/O wirings and power

supply voltage are all correct.

• Securely fasten installation and terminal screws.

• Set the operation mode switch to PROG mode.

Summary of Contents for Samsung NX-CPU700p



























































































































Search results

Summary of Contents for Samsung NX-CPU700p

Reviews:

Rockwell Automation Samsung NX-CPU700p, User Manual, Page: 6 / 122

Search results

Summary of Contents for Samsung NX-CPU700p

Reviews: