Rockwell Automation Samsung NX-CPU700p, User Manual, Page: 74 / 122

Share

Page: 74 / 122

Rockwell Automation Samsung NX-CPU700p User Manual Download Page 74

74

EEPROM Backup

What's EEPROM backup?

EEPROM (Electric Erase Programmable Read Only Memory) can retain
the data when the power is turned off, and erase or record data when
the power is turned on. This function allows you to retain the PLC
program when the power is turned off. And it also erases an existing
program and records a new one when correcting or storing a program
after turning on the power.

Applicable models

The types of EEPROM can be defined by its characteristics.
The CPUs for OE M

AX

NX70 (NX70-CPU70p1 and NX70-CPU70p2) PLC

use the flash memory.

This function is widely used since it is easy to use, store, and transfer
data, and is built in the NX70 PLC (NX70-CPU70p2).

EEPROM uses 29EE512 and has a minimum of 3000 times to write to
flash memory. It should be noted that the memory is to be changed
when exceeding the use of over 3,000 times.

Procedure

Backup using WinGPC

How to backup using WinGPC

Connect Online.
Save the completed program onto the PLC (Download: WinGPC =>
PLC).
Select the ‘EEPROM Backup (E)’ in the ‘Online’ menu.

DIP switch OFF

Operates with the program stored
in RAM using battery power.

DIP switch ON

Erases the contents of RAM and
copy the programs stored in
EEPROM onto RAM to operate.

Starts ‘EEPROM backup’ or
operates ‘EEPROM backup’ at
WinGPC

RAM

Operation

Battery

PLC Power ON

Program

stored in EEPROM

«
...
72
73
74
75
76
...
»

Summary of Contents for Samsung NX-CPU700p



























































































































Reviews:

No comments